Skip to main content

Tool

Peptide Reconstitution Calculator

Concentration equals the peptide mass divided by the diluent volume. Enter the vial mass, the volume of diluent and the amount wanted per aliquot to get the concentration in mg/mL, the volume that holds each aliquot, and the molar concentration for a selected compound.

Printed on the certificate of analysis. Leave at 100 if the COA does not report it.

Only compounds whose listed molecular weight matches their formula are shown.

Results

Concentration
2.5mg/mL
Volume per aliquot
100µL
Concentration
2,500mcg/mL
Volume per aliquot
0.1mL
Aliquots per vial
20whole
Peptide in vial
5mg net

Arithmetic for laboratory solution preparation only. Research use only; not for human or veterinary use.

How the calculation works

  • net peptide (mg) = vial mass (mg) × net peptide content (%) ÷ 100
  • concentration (mg/mL) = net peptide (mg) ÷ diluent volume (mL)
  • volume per aliquot (mL) = aliquot amount (mg) ÷ concentration (mg/mL)
  • aliquots per vial = net peptide (mg) ÷ aliquot amount (mg), rounded down
  • molarity (mM) = concentration (mg/mL) ÷ molecular weight (g/mol) × 1,000

mg/mL and mcg/µL are numerically the same, so 2.5 mg/mL means each microliter holds 2.5 mcg.

Worked example

A vial labelled 5 mg is reconstituted with 2 mL of diluent and divided into 250 mcg aliquots. Concentration is 5 ÷ 2 = 2.5 mg/mL. Each aliquot is 0.25 mg ÷ 2.5 mg/mL = 0.1 mL (100 µL), and the vial yields 5 ÷ 0.25 = 20 aliquots.

If the certificate of analysis reports 80% net peptide content, the vial holds 4 mg of peptide. The same 2 mL gives 2.0 mg/mL, each 250 mcg aliquot becomes 125 µL, and the vial yields 16 aliquots.

Choosing a diluent volume

The diluent volume does not change how much peptide is in the vial, only how concentrated the solution is. Less diluent gives a higher concentration and smaller aliquot volumes; more diluent gives lower concentration and larger volumes that are easier to measure precisely. Choose a volume where each aliquot falls comfortably within the measuring range of the pipette or syringe in use.

The diluent itself depends on the compound: sterile or bacteriostatic water suits most water-soluble peptides, while hydrophobic or basic sequences may need a dilute acid or a co-solvent. Check the supplier's solubility data before adding liquid.

Mass, net peptide content and purity

Three numbers on a certificate of analysis are easy to confuse. The labelled mass is the weight of lyophilized powder in the vial. Net peptide content is the share of that powder that is peptide, after counterions, water and excipients. HPLC purity is the share of the peptide material that is the target sequence rather than related impurities.

Only net peptide content changes the concentration you calculate. A 99% pure peptide with 80% net content still delivers 80% of the labelled mass as peptide.

Common mistakes

  • Entering mcg where mg is expected, or the reverse (a 1,000× error).
  • Confusing mL with µL when reading the volume per aliquot.
  • Treating labelled vial mass as pure peptide when the COA reports net content.
  • Using a molecular weight for the wrong salt form or a different sequence.

Frequently asked questions

How do you calculate peptide concentration after reconstitution?

Divide the mass of peptide in the vial by the volume of diluent added. 5 mg in 2 mL gives 2.5 mg/mL, which is the same as 2.5 mcg per microliter. If the certificate of analysis reports net peptide content below 100%, multiply the vial mass by that percentage first.

How much bacteriostatic water should be added to a 5 mg vial?

There is no single correct volume; the volume sets the concentration. 1 mL gives 5 mg/mL, 2 mL gives 2.5 mg/mL and 2.5 mL gives 2 mg/mL. Pick a volume that makes each aliquot large enough to measure accurately with the pipette or syringe in use, and confirm the compound dissolves in the chosen diluent.

What is net peptide content and why does it change the result?

A lyophilized peptide is not 100% peptide by weight: counterions such as TFA or acetate, residual water and any excipient make up the rest. Net peptide content, usually measured by amino acid analysis or nitrogen analysis, is the share that is peptide. HPLC purity is a different number: it reports how much of the peptide material is the target sequence.

How do you convert mg/mL to molar concentration?

mg/mL is the same as g/L. Divide it by the molecular weight in g/mol to get mol/L, then multiply by 1,000 for millimolar. 2.5 mg/mL of a 1,419.5 g/mol peptide is about 1.76 mM.

Is 1 mg the same as 1,000 mcg?

Yes. 1 mg equals 1,000 mcg (micrograms), and 1 mL equals 1,000 µL. Mixing up mg and mcg is the most common error in these calculations and changes the result by a factor of 1,000.

Compound data comes from each compound's Peptide Portal guide. For research and educational purposes only; not for human or veterinary use, and not medical advice.

Last reviewed Nov 9, 2026